How to Get Better GPS Accuracy with Your Rugged Handheld

How to get better GPS accuracyTo the average consumer, a soothing voice offering most-of-the-time-correct driving instructions to a good restaurant in an unfamiliar town is all that is required for total GPS satisfaction. “In one-hundred feet, turn right.” Thanks, talking car! However, the fact that you are reading this on Juniper Systems’ blog for data collection experts says that you are likely a professional trying to squeeze every last drop of precision out of your GPS receiver for accurately marking, tracking, and navigating back to assets or samplings.

What follows is a list of some basic best practices to improve GPS accuracy, applicable whether you are using a rugged handheld computer with navigation-grade internal GPS, or a more sophisticated precision receiver. As always, if you don’t find what you are looking for here, or are experiencing any difficulty while collecting data, contact a Juniper Systems expert for some helpful free advice.

Common GPS Problems and Solutions:

Problem #1: Obstructions

Because the GPS signal coming from the satellites is very faint, there are several objects that can prevent the direct line of GPS signals from reaching the GPS receiver, whether they are overhead or adjacent obstructions. These objects include mountains or other terrain, tree canopy, buildings, and your own body.

Solutions

  • Step away from the obstructed area until you’re in more of a clearing.
  • Hold the handheld computer and GPS receiver in a position such that the GPS antenna is facing away from all obstructions.
  • Use the manual point collection feature (instead of the timed interval collection feature) while mapping lines and polygons next to buildings or under tree canopy. This allows you to collect a point away from the obstruction and then connect it to a point taken at the end of the line (these points may need to be adjusted).
  • Watch your PDOP (position dilution of precision) settings. PDOP is an indirect measure of the accuracy of your position, so lower numbers are better, preferably less than three. Start out with a threshold setting of five and adjust up or down depending on conditions. Remember that a high threshold setting will make it easier to get a signal, but your accuracy will worsen, and vice versa. You may also try rotating your body to improve your PDOP.
  • Set the point averaging setting to collect more points. While you may gather accurate data when collecting an average of two or three points in a clear and unobstructed area, it is recommended that you collect an average of 10–20 points in obstructed areas. Keep in mind that it takes at least one second to collect each point, so if you are averaging 20 points, it will take a minimum of 20 seconds or even longer if your PDOP is high and conditions are poor.

Problem #2: Multipath or Signal Reflection

Multipath errors or signal reflection occur when the GPS signal reflects off of buildings or other objects, resulting in multiple delayed signals. Since the GPS system works off of time, anything that causes delays can result in errors in position. The GPS receiver picks up the direct GPS signal and detects the reflected signals, therefore disrupting the accurate data already collected by the handheld. If you are near a building and your GPS is showing 12 of 12 satellites are visible, yet your GPS position is bouncing around on the screen, it is very possible that some multipath errors are occurring in which some satellites are being counted twice by the GPS receiver.

Solutions

  • Stand with your back to the building, resulting in the GPS antenna pointing away from the obstruction.
  • Watch your PDOP settings. Start out with a threshold setting of five and adjust up or down depending on conditions. Remember that a high threshold setting will make it easier to get a signal, but your accuracy will worsen, and vice versa. You may also try rotating your body to improve your PDOP.
  • Record an offset point measurement at some distance away from the intended measurement point, then enter a manually edited point based on the offset point location.

Problem #3: Map Error

When using GPS with a handheld computer, you have several options of background imagery or aerial photography to use as your base map. Often times, the base map will not be referenced to the same datum or projection as the GPS receiver, resulting in discrepancies between the object’s actual GPS coordinates and where it is mapped on the base map displayed on the handheld. For example, the GPS receiver data may be reported in WGS84 datum, while the aerial photography is reported in a different projection, such as NAD83. This results in a mismatch of data that can reach up to 4–6 feet or more.

Another reason for map error is simply because the map was created in the past and is now outdated. Items such as roads and buildings may not have existed when the map was created. Changes in elevation, photography angles, and the curvature of the earth may also affect the accuracy of the imagery.

Solutions

  • Change your map so its datum or projection matches the GPS receiver.
  • Remember that you may have the capability of manually editing and adjusting the point positions, depending on the type of mapping software you are using. As you manually move points, be sure that the software you are using automatically changes the GPS coordinates to the correct location to maintain accuracy.

 General Suggestions for Better GPS Accuracy

  • If mapping close to a building or other obstructions, try to stay more than twice the height of the building away. This isn’t possible in all cases, but it is a good rule of thumb to remember.
  • Try to keep as many satellites visible as possible. At any location on earth, up to 12 satellites may be visible, so 11 out of 12 or 12 out of 12 satellites will produce the most accurate results. Simply turning and facing different directions can help increase the number of satellites in view.
  • If you are standing still and the GPS point starts bouncing around, this most likely means that there is interference nearby affecting your signal. The best way to avoid this is to walk away from overhead obstructions and into more of a clearing.

If you are already following the tips above, but still require a greater level of GPS accuracy, we can help you find the equipment and knowledge to do it. Please give us a call at 435.753.1881 or send us an email.

What ways have you found to improve GPS accuracy? Share with us in the comments below.

 

 

3 Comments

  1. Great post. never though about thinking about obstructions

  2. Great advice! I’m glad you didn’t say “wear a tinfoil hat”! haha.

Leave a Reply

%d bloggers like this: